Internet-Draft MLRsearch July 2025
Konstantynowicz & Polak Expires 8 January 2026 [Page]
Workgroup:
Benchmarking Working Group
Internet-Draft:
draft-ietf-bmwg-mlrsearch-11
Published:
Intended Status:
Informational
Expires:
Authors:
M. Konstantynowicz
Cisco Systems
V. Polak
Cisco Systems

Multiple Loss Ratio Search

Abstract

This document specifies extensions to "Benchmarking Methodology for Network Interconnect Devices" (RFC 2544) throughput search by defining a new methodology called Multiple Loss Ratio search (MLRsearch). MLRsearch aims to minimize search duration, support multiple loss ratio searches, and improve result repeatability and comparability.

MLRsearch is motivated by the pressing need to address the challenges of evaluating and testing the various data plane solutions, especially in software- based networking systems based on Commercial Off-the-Shelf (COTS) CPU hardware vs purpose-built ASIC / NPU / FPGA hardware.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 8 January 2026.

Table of Contents

1. Introduction

This document describes the Multiple Loss Ratio search (MLRsearch) methodology, optimized for determining data plane throughput in software-based networking functions running on commodity systems with x86/ARM CPUs (vs purpose-built ASIC / NPU / FPGA). Such network functions can be deployed on dedicated physical appliance (e.g., a standalone hardware device) or as virtual appliance (e.g., Virtual Network Function running on shared servers in the compute cloud).

1.1. Purpose

The purpose of this document is to describe the Multiple Loss Ratio search (MLRsearch) methodology, optimized for determining data plane throughput in software-based networking devices and functions.

Applying the vanilla throughput binary search, as specified for example in [TST009] and [RFC2544] to software devices under test (DUTs) results in several problems:

  • Binary search takes long as most trials are done far from the eventually found throughput.

  • The required final trial duration and pauses between trials prolong the overall search duration.

  • Software DUTs show noisy trial results, leading to a big spread of possible discovered throughput values.

  • Throughput requires a loss of exactly zero frames, but the industry best practices frequently allow for low but non-zero losses tolerance ([Y.1564], test-equipment manuals).

  • The definition of throughput is not clear when trial results are inconsistent. (e.g., when successive trials at the same - or even a higher - offered load yield different loss ratios, the classical [RFC1242] / [RFC2544] throughput metric can no longer be pinned to a single, unambiguous value.)

To address these problems, early MLRsearch implementations employed the following enhancements:

  1. Allow multiple short trials instead of one big trial per load.

    • Optionally, tolerate a percentage of trial results with higher loss.

  2. Allow searching for multiple Search Goals, with differing loss ratios.

    • Any trial result can affect each Search Goal in principle.

  3. Insert multiple coarse targets for each Search Goal, earlier ones need to spend less time on trials.

    • Earlier targets also aim for lesser precision.

    • Use Forwarding Rate (FR) at Maximum Offered Load (FRMOL), as defined in Section 3.6.2 of [RFC2285], to initialize bounds.

  4. Be careful when dealing with inconsistent trial results.

    • Reported throughput is smaller than the smallest load with high loss.

    • Smaller load candidates are measured first.

  5. Apply several time-saving load selection heuristics that deliberately prevent the bounds from narrowing unnecessarily.

Enhacements 1, 2 and partly 4 are formalized as MLRsearch Specification within this document, other implementation details are out the scope.

The remaining enhancements are treated as implementation details, thus achieving high comparability without limiting future improvements.

MLRsearch configuration supports both conservative settings and aggressive settings. Conservative enough settings lead to results unconditionally compliant with [RFC2544], but without much improvement on search duration and repeatability - see MLRsearch Compliant with RFC 2544 (Section 4.10.2). Conversely, aggressive settings lead to shorter search durations and better repeatability, but the results are not compliant with [RFC2544]. Exact settings are not specified, but see the discussion in Overview of RFC 2544 Problems (Section 2) for the impact of different settings on result quality.

This document does not change or obsolete any part of [RFC2544].

1.2. Positioning within BMWG Methodologies

The Benchmarking Methodology Working Group (BMWG) produces recommendations (RFCs) that describe various benchmarking methodologies for use in a controlled laboratory environment. A large number of these benchmarks are based on the terminology from [RFC1242] and the foundational methodology from [RFC2544]. A common pattern has emerged where BMWG documents reference the methodology of [RFC2544] and augment it with specific requirements for testing particular network systems or protocols, without modifying the core benchmark definitions.

While BMWG documents are formally recommendations, they are widely treated as industry norms to ensure the comparability of results between different labs. The set of benchmarks defined in [RFC2544], in particular, became a de facto standard for performance testing. In this context, the MLRsearch Specification formally defines a new class of benchmarks that fits within the wider [RFC2544] framework (see Scope (Section 4.1)).

A primary consideration in the design of MLRsearch is the trade-off between configurability and comparability. The methodology's flexibility, especially the ability to define various sets of Search Goals, supporting both single-goal and multiple-goal benchmarks in an unified way is powerful for detailed characterization and internal testing. However, this same flexibility is detrimental to inter-lab comparability unless a specific, common set of Search Goals is agreed upon.

Therefore, MLRsearch should not be seen as a direct extension nor a replacement for the [RFC2544] Throughput benchmark. Instead, this document provides a foundational methodology that future BMWG documents can use to define new, specific, and comparable benchmarks by mandating particular Search Goal configurations. For operators of existing test procedures, it is worth noting that many test setups measuring [RFC2544] Throughput can be adapted to produce results compliant with the MLRsearch Specification, often without affecting Trials, merely by augmenting the content of the final test report.

2. Overview of RFC 2544 Problems

This section describes the problems affecting usability of various performance testing methodologies, mainly a binary search for [RFC2544] unconditionally compliant throughput.

2.1. Long Search Duration

The proliferation of software DUTs, with frequent software updates and a

number of different frame processing modes and configurations, has increased both the number of performance tests required to verify the DUT update and the frequency of running those tests. This makes the overall test execution time even more important than before.

The throughput definition per [RFC2544] restricts the potential for time-efficiency improvements. The bisection method, when used in a manner unconditionally compliant with [RFC2544], is excessively slow due to two main factors.

Firstly, a significant amount of time is spent on trials with loads that, in retrospect, are far from the final determined throughput.

Secondly, [RFC2544] does not specify any stopping condition for throughput search, so users of testing equipment implementing the procedure already have access to a limited trade-off between search duration and achieved precision. However, each of the full 60-second trials doubles the precision.

As such, not many trials can be removed without a substantial loss of precision.

For reference, here is a brief [RFC2544] throughput binary (bisection) reminder, based on Sections 24 and 26 of [RFC2544:

  • Set Max = line-rate and Min = a proven loss-free load.

  • Run a single 60-s trial at the midpoint.

  • Zero-loss -> midpoint becomes new Min; any loss-> new Max.

  • Repeat until the Max-Min gap meets the desired precision, then report the highest zero-loss rate for every mandatory frame size.

2.2. DUT in SUT

[RFC2285] defines:

DUT as:

  • The network frame forwarding device to which stimulus is offered and response measured Section 3.1.1 of [RFC2285].

SUT as:

  • The collective set of network devices as a single entity to which stimulus is offered and response measured Section 3.1.2 of [RFC2285].

Section 19 of [RFC2544] specifies a test setup with an external tester stimulating the networking system, treating it either as a single Device Under Test (DUT), or as a system of devices, a System Under Test (SUT).

For software-based data-plane forwarding running on commodity x86/ARM CPUs, the SUT comprises not only the forwarding application itself, the DUT, but the entire execution environment: host hardware, firmware and kernel/hypervisor services, as well as any other software workloads that share the same CPUs, memory and I/O resources.

Given that a SUT is a shared multi-tenant environment, the DUT might inadvertently experience interference from the operating system or other software operating on the same server.

Some of this interference can be mitigated. For instance, in multi-core CPU systems, pinning DUT program threads to specific CPU cores and isolating those cores can prevent context switching.

Despite taking all feasible precautions, some adverse effects may still impact the DUT's network performance. In this document, these effects are collectively referred to as SUT noise, even if the effects are not as unpredictable as what other engineering disciplines call noise.

A DUT can also exhibit fluctuating performance itself, for reasons not related to the rest of SUT. For example, this can be due to pauses in execution as needed for internal stateful processing. In many cases this may be an expected per-design behavior, as it would be observable even in a hypothetical scenario where all sources of SUT noise are eliminated. Such behavior affects trial results in a way similar to SUT noise. As the two phenomena are hard to distinguish, in this document the term 'noise' is used to encompass both the internal performance fluctuations of the DUT and the genuine noise of the SUT.

A simple model of SUT performance consists of an idealized noiseless performance, and additional noise effects. For a specific SUT, the noiseless performance is assumed to be constant, with all observed performance variations being attributed to noise. The impact of the noise can vary in time, sometimes wildly, even within a single trial. The noise can sometimes be negligible, but frequently it lowers the observed SUT performance as observed in trial results.

In this simple model, a SUT does not have a single performance value, it has a spectrum. One end of the spectrum is the idealized noiseless performance value, the other end can be called a noiseful performance. In practice, trial results close to the noiseful end of the spectrum happen only rarely. The worse a possible performance value is, the more rarely it is seen in a trial. Therefore, the extreme noiseful end of the SUT spectrum is not observable among trial results.

Furthermore, the extreme noiseless end of the SUT spectrum is unlikely to be observable, this time because minor noise events almost always occur during each trial, nudging the measured performance slightly below the theoretical maximum.

Unless specified otherwise, this document's focus is on the potentially observable ends of the SUT performance spectrum, as opposed to the extreme ones.

When focusing on the DUT, the benchmarking effort should ideally aim to eliminate only the SUT noise from SUT measurements. However, this is currently not feasible in practice, as there are no realistic enough models that would be capable to distinguish SUT noise from DUT fluctuations (based on the available literature at the time of writing).

Provided SUT execution environment and any co-resident workloads place only negligible demands on SUT shared resources, so that the DUT remains the principal performance limiter, the DUT's ideal noiseless performance is defined as the noiseless end of the SUT performance spectrum.

Note that by this definition, DUT noiseless performance also minimizes the impact of DUT fluctuations, as much as realistically possible for a given trial duration.

The MLRsearch methodology aims to solve the DUT in SUT problem by estimating the noiseless end of the SUT performance spectrum using a limited number of trial results.

Improvements to the throughput search algorithm, aimed at better dealing with software networking SUT and DUT setups, should adopt methods that explicitly model SUT-generated noise, enabling to derive surrogate metrics that approximate the (proxies for) DUT noiseless performance across a range of SUT noise-tolerance levels.

2.3. Repeatability and Comparability

[RFC2544] does not suggest repeating throughput search. Also, note that from simply one discovered throughput value, it cannot be determined how repeatable that value is. Unsatisfactory repeatability then leads to unacceptable comparability, as different benchmarking teams may obtain varying throughput values for the same SUT, exceeding the expected differences from search precision. Repeatability is important also when the test procedure is kept the same, but SUT is varied in small ways. For example, during development of software-based DUTs, repeatability is needed to detect small regressions.

[RFC2544] throughput requirements (60 seconds trial and no tolerance of a single frame loss) affect the throughput result as follows:

The SUT behavior close to the noiseful end of its performance spectrum consists of rare occasions of significantly low performance, but the long trial duration makes those occasions not so rare on the trial level. Therefore, the binary search results tend to wander away from the noiseless end of SUT performance spectrum, more frequently and more widely than shorter trials would, thus causing unacceptable throughput repeatability.

The repeatability problem can be better addressed by defining a search procedure that identifies a consistent level of performance, even if it does not meet the strict definition of throughput in [RFC2544].

According to the SUT performance spectrum model, better repeatability will be at the noiseless end of the spectrum. Therefore, solutions to the DUT in SUT problem will help also with the repeatability problem.

Conversely, any alteration to [RFC2544] throughput search that improves repeatability should be considered as less dependent on the SUT noise.

An alternative option is to simply run a search multiple times, and report some statistics (e.g., average and standard deviation, and/or percentiles like p95).

This can be used for a subset of tests deemed more important, but it makes the search duration problem even more pronounced.

2.4. Throughput with Non-Zero Loss

Section 3.17 of [RFC1242] defines throughput as:

The maximum rate at which none of the offered frames are dropped by the device.

Then, it says:

Since even the loss of one frame in a data stream can cause significant delays while waiting for the higher-level protocols to time out, it is useful to know the actual maximum data rate that the device can support.

However, many benchmarking teams accept a low, non-zero loss ratio as the goal for their load search.

Motivations are many:

  • Networking protocols tolerate frame loss better, compared to the time when [RFC1242] and [RFC2544] were specified.

  • Increased link speeds require trials sending way more frames within the same duration, increasing the chance of a small SUT performance fluctuation being enough to cause frame loss.

  • Because noise-related drops usually arrive in small bursts, their impact on the trial's overall frame loss ratio is diluted by the longer intervals in which the SUT operates close to its noiseless performance; consequently, the averaged Trial Loss Ratio can still end up below the specified Goal Loss Ratio value.

  • For more information, see an earlier draft [Lencze-Shima] (Section 5) and references there.

Regardless of the validity of all similar motivations, support for non-zero loss goals makes a search algorithm more user-friendly. [RFC2544] throughput is not user-friendly in this regard.

Furthermore, allowing users to specify multiple loss ratio values, and enabling a single search to find all relevant bounds, significantly enhances the usefulness of the search algorithm.

Searching for multiple Search Goals also helps to describe the SUT performance spectrum better than the result of a single Search Goal. For example, the repeated wide gap between zero and non-zero loss loads indicates the noise has a large impact on the observed performance, which is not evident from a single goal load search procedure result.

It is easy to modify the vanilla bisection to find a lower bound for the load that satisfies a non-zero Goal Loss Ratio. But it is not that obvious how to search for multiple goals at once, hence the support for multiple Search Goals remains a problem.

At the time of writing there does not seem to be a consensus in the industry on which ratio value is the best. For users, performance of higher protocol layers is important, for example, goodput of TCP connection (TCP throughput, [RFC6349]), but relationship between goodput and loss ratio is not simple. Refer to [Lencze-Kovacs-Shima] for examples of various corner cases, Section 3 of [RFC6349] for loss ratios acceptable for an accurate measurement of TCP throughput, and [Ott-Mathis-Semke-Mahdavi] for models and calculations of TCP performance in presence of packet loss.

2.5. Inconsistent Trial Results

While performing throughput search by executing a sequence of measurement trials, there is a risk of encountering inconsistencies between trial results.

Examples include, but are not limited to:

  • A trial at the same load (same or different trial duration) results in a different Trial Loss Ratio.

  • A trial at a larger load (same or different trial duration) results in a lower Trial Loss Ratio.

The plain bisection never encounters inconsistent trials. But [RFC2544] hints about the possibility of inconsistent trial results, in two places in its text. The first place is Section 24 of [RFC2544], where full trial durations are required, presumably because they can be inconsistent with the results from short trial durations. The second place is Section 26.3 of [RFC2544], where two successive zero-loss trials are recommended, presumably because after one zero-loss trial there can be a subsequent inconsistent non-zero-loss trial.

A robust throughput search algorithm needs to decide how to continue the search in the presence of such inconsistencies. Definitions of throughput in [RFC1242] and [RFC2544] are not specific enough to imply a unique way of handling such inconsistencies.

Ideally, there will be a definition of a new quantity which both generalizes throughput for non-zero Goal Loss Ratio values (and other possible repeatability enhancements), while being precise enough to force a specific way to resolve trial result inconsistencies. But until such a definition is agreed upon, the correct way to handle inconsistent trial results remains an open problem.

Relevant Lower Bound is the MLRsearch term that addresses this problem.

3. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14, [RFC2119] and [RFC8174] when, and only when, they appear in all capitals, as shown here.

This document is categorized as an Informational RFC. While it does not mandate the adoption of the MLRsearch methodology, it uses the normative language of BCP 14 to provide an unambiguous specification. This ensures that if a test procedure or test report claims compliance with the MLRsearch Specification, it MUST adhere to all the absolute requirements defined herein. The use of normative language is intended to promote repeatable and comparable results among those who choose to implement this methodology.

4. MLRsearch Specification

This chapter provides all technical definitions needed for evaluating whether a particular test procedure complies with MLRsearch Specification.

Some terms used in the specification are capitalized. It is just a stylistic choice for this document, reminding the reader this term is introduced, defined or explained elsewhere in the document. Lowercase variants are equally valid.

This document does not separate terminology from methodology. Terms are fully specified and discussed in their own subsections, under sections titled "Terms". This way, the list of terms is visible in table of contents.

Each per term subsection contains a short Definition paragraph containing a minimal definition and all strict requirements, followed by Discussion paragraphs focusing on important consequences and recommendations. Requirements about how other components can use the defined quantity are also included in the discussion.

4.1. Scope

This document specifies the Multiple Loss Ratio search (MLRsearch) methodology. The MLRsearch Specification details a new class of benchmarks by listing all terminology definitions and methodology requirements. The definitions support "multi-goal" benchmarks, with "single-goal" as a subset.

The normative scope of this specification includes:

  • The terminology for all required quantities and their attributes.

  • An abstract architecture consisting of functional components (Manager, Controller, Measurer) and the requirements for their inputs and outputs.

  • The required structure and attributes of the Controller Input, including one or more Search Goal instances.

  • The required logic for Load Classification, which determines whether a given Trial Load qualifies as a Lower Bound or an Upper Bound for a Search Goal.

  • The required structure and attributes of the Controller Output, including a Goal Result for each Search Goal.

4.1.1. Relationship to RFC 2544

MLRsearch Specification is an independent methodology and does not change or obsolete any part of [RFC2544].

This specification permits deviations from the Trial procedure as described in [RFC2544]. Any deviation from the [RFC2544] procedure must be documented explicitly in the Test Report, and such variations remain outside the scope of the original [RFC2544] benchmarks.

A specific single-goal MLRsearch benchmark can be configured to be compliant with [RFC2544] Throughput, and most procedures reporting [RFC2544] Throughput can be adapted to satisfy also MLRsearch requirements for specific search goal.

4.1.2. Applicability of Other Specifications

Methodology extensions from other BMWG documents that specify details for testing particular DUTs, configurations, or protocols (e.g., by defining a particular Traffic Profile) are considered orthogonal to MLRsearch and are applicable to a benchmark conducted using MLRsearch methodology.

4.1.3. Out of Scope

The following aspects are explicitly out of the normative scope of this document:

  • This specification does not mandate or recommend any single, universal Search Goal configuration for all use cases. The selection of Search Goal parameters is left to the operator of the test procedure or may be defined by future specifications.

  • The internal heuristics or algorithms used by the Controller to select Trial Input values (e.g., the load selection strategy) are considered implementation details.

  • The potential for, and the effects of, interference between different Search Goal instances within a multiple-goal search are considered outside the normative scope of this specification.

4.2. Architecture Overview

Although the normative text references only terminology that has already been introduced, explanatory passages beside it sometimes profit from terms that are defined later in the document. To keep the initial read-through clear, this informative section offers a concise, top-down sketch of the complete MLRsearch architecture.

The architecture is modelled as a set of abstract, interacting components. Information exchange between components is expressed in an imperative-programming style: one component "calls" another, supplying inputs (arguments) and receiving outputs (return values). This notation is purely conceptual; actual implementations need not exchange explicit messages. When the text contrasts alternative behaviours, it refers to the different implementations of the same component.

A test procedure is considered compliant with the MLRsearch Specification if it can be conceptually decomposed into the abstract components defined herein, and each component satisfies the requirements defined for its corresponding MLRsearch element.

The Measurer component is tasked to perform Trials, the Controller component is tasked to select Trial Durations and Loads, the Manager component is tasked to pre-configure involved entities and to produce the Test Report. The Test Report explicitly states Search Goals (as Controller Input) and corresponding Goal Results (Controller Output).

This constitutes one benchmark (single-goal or multi-goal). Repeated or slightly differing benchmarks are realized by calling Controller once for each benchmark.

The Manager calls a Controller once, and the Controller then invokes the Measurer repeatedly until Controler decides it has enough information to return outputs.

The part during which the Controller invokes the Measurer is termed the Search. Any work the Manager performs either before invoking the Controller or after Controller returns, falls outside the scope of the Search.

MLRsearch Specification prescribes Regular Search Results and recommends corresponding search completion conditions.

Irregular Search Results are also allowed, they have different requirements and their corresponding stopping conditions are out of scope.

Search Results are based on Load Classification. When measured enough, a chosen Load can either achieve or fail each Search Goal (separately), thus becoming a Lower Bound or an Upper Bound for that Search Goal.

When the Relevant Lower Bound is close enough to Relevant Upper Bound according to Goal Width, the Regular Goal Result is found. Search stops when all Regular Goal Results are found, or when some Search Goals are proven to have only Irregular Goal Results.

4.2.1. Test Report

A primary responsibility of the Manager is to produce a Test Report, which serves as the final and formal output of the test procedure.

This document does not provide a single, complete, normative definition for the structure of the Test Report. For example, Test Report may contain results for a single benchmark, or it could aggregate results of many benchmarks.

Instead, normative requirements for the content of the Test Report are specified throughout this document in conjunction with the definitions of the quantities and procedures to which they apply. Readers should note that any clause requiring a value to be "reported" or "stated in the test report" constitutes a normative requirement on the content of this final artifact.

Even where not stated explicitly, the "Reporting format" paragraphs in [RFC2544] sections are still requirements on Test Report if they apply to a MLRsearch benchmark.

4.2.2. Behavior Correctness

MLRsearch Specification by itself does not guarantee that the Search ends in finite time, as the freedom the Controller has for Load selection also allows for clearly deficient choices.

For deeper insights on these matters, refer to [FDio-CSIT-MLRsearch].

The primary MLRsearch implementation, used as the prototype for this specification, is [PyPI-MLRsearch].

4.3. Quantities

MLRsearch Specification uses a number of specific quantities, some of them can be expressed in several different units.

In general, MLRsearch Specification does not require particular units to be used, but it is REQUIRED for the test report to state all the units. For example, ratio quantities can be dimensionless numbers between zero and one, but may be expressed as percentages instead.

For convenience, a group of quantities can be treated as a composite quantity. One constituent of a composite quantity is called an attribute. A group of attribute values is called an instance of that composite quantity.

Some attributes may depend on others and can be calculated from other attributes. Such quantities are called derived quantities.

4.3.1. Current and Final Values

Some quantities are defined in a way that makes it possible to compute their values in the middle of a Search. Other quantities are specified so that their values can be computed only after a Search ends. Some quantities are important only after a Search ended, but their values are computable also before a Search ends.

For a quantity that is computable before a Search ends, the adjective current is used to mark a value of that quantity available before the Search ends. When such value is relevant for the search result, the adjective final is used to denote the value of that quantity at the end of the Search.

If a time evolution of such a dynamic quantity is guided by configuration quantities, those adjectives can be used to distinguish quantities. For example, if the current value of "duration" (dynamic quantity) increases from "initial duration" to "final duration" (configuration quantities), all the quoted names denote separate but related quantities. As the naming suggests, the final value of "duration" is expected to be equal to "final duration" value.

4.4. Existing Terms

This specification relies on the following three documents that should be consulted before attempting to make use of this document:

  • "Benchmarking Terminology for Network Interconnect Devices" [RFC1242] contains basic term definitions.

  • "Benchmarking Terminology for LAN Switching Devices" [RFC2285] adds more terms and discussions, describing some known network benchmarking situations in a more precise way.

  • "Benchmarking Methodology for Network Interconnect Devices" [RFC2544] contains discussions about terms and additional methodology requirements.

Definitions of some central terms from above documents are copied and discussed in the following subsections.

4.4.1. SUT

Defined in Section 3.1.2 of [RFC2285] as follows.

Definition:

 

The collective set of network devices to which stimulus is offered as a single entity and response measured.

Discussion:

 

An SUT consisting of a single network device is allowed by this definition.

 

In software-based networking SUT may comprise multitude of networking applications and the entire host hardware and software execution environment.

 

SUT is the only entity that can be benchmarked directly, even though only the performance of some sub-components are of interest.

4.4.2. DUT

Defined in Section 3.1.1 of [RFC2285] as follows.

Definition:

 

The network forwarding device to which stimulus is offered and response measured.

Discussion:

 

Contrary to SUT, the DUT stimulus and response are frequently initiated and observed only indirectly, on different parts of SUT.

 

DUT, as a sub-component of SUT, is only indirectly mentioned in MLRsearch Specification, but is of key relevance for its motivation. The device can represent a software-based networking functions running on commodity x86/ARM CPUs (vs purpose-built ASIC / NPU / FPGA).

 

A well-designed SUTs should have the primary DUT as their performance bottleneck. The ways to achieve that are outside of MLRsearch Specification scope.

4.4.3. Trial

A trial is the part of the test described in Section 23 of [RFC2544].

Definition:

 

A particular test consists of multiple trials. Each trial returns one piece of information, for example the loss rate at a particular input frame rate. Each trial consists of a number of phases:

 

a) If the DUT is a router, send the routing update to the "input" port and pause two seconds to be sure that the routing has settled.

 

b) Send the "learning frames" to the "output" port and wait 2 seconds to be sure that the learning has settled. Bridge learning frames are frames with source addresses that are the same as the destination addresses used by the test frames. Learning frames for other protocols are used to prime the address resolution tables in the DUT. The formats of the learning frame that should be used are shown in the Test Frame Formats document.

 

c) Run the test trial.

 

d) Wait for two seconds for any residual frames to be received.

 

e) Wait for at least five seconds for the DUT to restabilize.

Discussion:

 

The traffic is sent only in phase c) and received in phases c) and d).

 

Trials are the only stimuli the SUT is expected to experience during the Search.

 

In some discussion paragraphs, it is useful to consider the traffic as sent and received by a tester, as implicitly defined in Section 6 of [RFC2544].

 

The definition describes some traits, not using capitalized verbs to signify strength of the requirements. For the purposes of the MLRsearch Specification, the test procedure MAY deviate from the [RFC2544] description, but any such deviation MUST be described explicitly in the Test Report. It is still RECOMMENDED to not deviate from the description, as any deviation weakens comparability.

 

An example of deviation from [RFC2544] is using shorter wait times, compared to those described in phases a), b), d) and e).

 

The [RFC2544] document itself seems to be treating phase b) as any type of configuration that cannot be configured only once (by Manager, before Search starts), as some crucial SUT state could time-out during the Search. It is RECOMMENDED to interpret the "learning frames" to be any such time-sensitive per-trial configuration method, with bridge MAC learning being only one possible examples. Appendix C.2.4.1 of [RFC2544] lists another example: ARP with wait time of 5 seconds.

 

Some methodologies describe recurring tests. If those are based on Trials, they are treated as multiple independent Trials.

4.5. Trial Terms

This section defines new and redefine existing terms for quantities relevant as inputs or outputs of a Trial, as used by the Measurer component. This includes also any derived quantities related to results of one Trial.

4.5.1. Trial Duration

Definition:

 

Trial Duration is the intended duration of the phase c) of a Trial.

Discussion:

 

The value MUST be positive.

 

While any positive real value may be provided, some Measurer implementations MAY limit possible values, e.g., by rounding down to nearest integer in seconds. In that case, it is RECOMMENDED to give such inputs to the Controller so that the Controller only uses the accepted values.

4.5.2. Trial Load

Definition:

 

Trial Load is the per-interface Intended Load for a Trial.

Discussion:

 

Trial Load is equivalent to the quantities defined as constant load (Section 3.4 of [RFC1242]), data rate (Section 14 of [RFC2544]), and Intended Load (Section 3.5.1 of [RFC2285]), in the sense that all three definitions specify that this value applies to one (input or output) interface.

 

For specification purposes, it is assumed that this is a constant load by default, as specified in Section 3.4 of [RFC1242]). Informally, Traffic Load is a single number that can "scale" any traffic pattern as long as the intuition of load intended against a single interface can be applied.

 

It MAY be possible to use a Trial Load value to describe a non-constant traffic (using average load when the traffic consists of repeated bursts of frames e.g., as suggested in Section 21 of [RFC2544]). In the case of a non-constant load, the Test Report MUST explicitly mention how exactly non-constant the traffic is and how it reacts to Traffic Load value. But the rest of the MLRsearch Specification assumes that is not the case, to avoid discussing corner cases (e.g., which values are possible within medium limitations).

 

Similarly, traffic patterns where different interfaces are subject to different loads MAY be described by a single Trial Load value (e.g. using largest load among interfaces), but again the Test Report MUST explicitly describe how the traffic pattern reacts to Traffic Load value, and this specification does not discuss all the implications of that approach.

 

In the common case of bidirectional traffic, as described in Section 14. Bidirectional Traffic of [RFC2544], Trial Load is the data rate per direction, half of aggregate data rate.

 

Traffic patterns where a single Trial Load does not describe their scaling cannot be used for MLRsearch benchmarks.

 

Similarly to Trial Duration, some Measurers MAY limit the possible values of Trial Load. Contrary to Trial Duration, documenting such behavior in the test report is OPTIONAL. This is because the load differences are negligible (and frequently undocumented) in practice.

 

The Controller MAY select Trial Load and Trial Duration values in a way that would not be possible to achieve using any integer number of data frames.

 

If a particular Trial Load value is not tied to a single Trial, e.g., if there are no Trials yet or if there are multiple Trials, this document uses a shorthand Load.

 

The test report MAY present the aggregate load across multiple interfaces, treating it as the same quantity expressed using different units. Each reported Trial Load value MUST state unambiguously whether it refers to (i) a single interface, (ii) a specified subset of interfaces (e.g., such as all logical interfaces mapped to one physical port), or (iii) the total across every interface. For any aggregate load value, the report MUST also give the fixed conversion factor that links the per-interface and multi-interface load values.

 

The per-interface value remains the primary unit, consistent with prevailing practice in [RFC1242], [RFC2544], and [RFC2285].

 

The last paragraph also applies to other terms related to Load.

 

For example, tests with symmetric bidirectional traffic can report load-related values as "bidirectional load" (double of "unidirectional load").

4.5.3. Trial Input

Definition:

 

Trial Input is a composite quantity, consisting of two attributes: Trial Duration and Trial Load.

Discussion:

 

When talking about multiple Trials, it is common to say "Trial Inputs" to denote all corresponding Trial Input instances.

 

A Trial Input instance acts as the input for one call of the Measurer component.

 

Contrary to other composite quantities, MLRsearch implementations MUST NOT add optional attributes into Trial Input. This improves interoperability between various implementations of a Controller and a Measurer.

 

Note that both attributes are intended quantities, as only those can be fully controlled by the Controller. The actual offered quantities, as realized by the Measurer, can be different (and must be different if not multiplying into integer number of frames), but questions around those offered quantities are generally outside of the scope of this document.

4.5.4. Traffic Profile

Definition:

 

Traffic Profile is a composite quantity containing all attributes other than Trial Load and Trial Duration, that are needed for unique determination of the Trial to be performed.

Discussion:

 

All the attributes are assumed to be constant during the Search, and the composite is configured on the Measurer by the Manager before the Search starts. This is why the traffic profile is not part of the Trial Input.

 

Specification of traffic properties included in the Traffic Profile is the responsibility of the Manager, but the specific configuration mechanisms are outside of the scope of this docunment.

 

Informally, implementations of the Manager and the Measurer must be aware of their common set of capabilities, so that Traffic Profile instance uniquely defines the traffic during the Search. Typically, Manager and Measurer implementations are tightly integrated.

 

Integration efforts between independent Manager and Measurer implementations are outside of the scope of this document. An example standardization effort is [Vassilev], a draft at the time of writing.

 

Examples of traffic properties include: - Data link frame size - Fixed sizes as listed in Section 3.5 of [RFC1242] and in Section 9 of [RFC2544] - IMIX mixed sizes as defined in [RFC6985] - Frame formats and protocol addresses - Section 8, 12 and Appendix C of [RFC2544] - Symmetric bidirectional traffic - Section 14 of [RFC2544].

 

Other traffic properties that need to be somehow specified in Traffic Profile, and MUST be mentioned in Test Report if they apply to the benchmark, include:

 
  • bidirectional traffic from Section 14 of [RFC2544],

  • fully meshed traffic from Section 3.3.3 of [RFC2285],

  • modifiers from Section 11 of [RFC2544].

  • IP version mixing from Section 5.3 of [RFC8219].

4.5.5. Trial Forwarding Ratio

Definition:

 

The Trial Forwarding Ratio is a dimensionless floating point value. It MUST range between 0.0 and 1.0, both inclusive. It is calculated by dividing the number of frames successfully forwarded by the SUT by the total number of frames expected to be forwarded during the trial.

Discussion:

 

For most Traffic Profiles, "expected to be forwarded" means "intended to get received by SUT from tester". This SHOULD be the default interpretation. Only if this is not the case, the test report MUST describe the Traffic Profile in a detail sufficient to imply how Trial Forwarding Ratio should be calculated.

 

Trial Forwarding Ratio MAY be expressed in other units (e.g., as a percentage) in the test report.

 

Note that, contrary to Load terms, frame counts used to compute Trial Forwarding Ratio are generally aggregates over all SUT output interfaces, as most test procedures verify all outgoing frames. The procedure for [RFC2544] Throughput counts received frames, so implicitly it implies bidirectional counts for bidirectional traffic, even though the final value is "rate" that is still per-interface.

 

For example, in a test with symmetric bidirectional traffic, if one direction is forwarded without losses, but the opposite direction does not forward at all, the Trial Forwarding Ratio would be 0.5 (50%).

 

In future extensions, more general ways to compute Trial Forwarding Ratio may be allowed, but the current MLRsearch Specification relies on this specific averaged counters approach.

4.5.6. Trial Loss Ratio

Definition:

 

The Trial Loss Ratio is equal to one minus the Trial Forwarding Ratio.

Discussion:

 

100% minus the Trial Forwarding Ratio, when expressed as a percentage.

 

This is almost identical to Frame Loss Rate of Section 3.6 of [RFC1242]. The only minor differences are that Trial Loss Ratio does not need to be expressed as a percentage, and Trial Loss Ratio is explicitly based on averaged frame counts when more than one data stream is present.

4.5.7. Trial Forwarding Rate

Definition:

 

The Trial Forwarding Rate is a derived quantity, calculated by multiplying the Trial Load by the Trial Forwarding Ratio.

Discussion:

 

This quantity differs from the Forwarding Rate described in Section 3.6.1 of [RFC2285]. Under the RFC 2285 method, each output interface is measured separately, so every interface may report a distinct rate. The Trial Forwarding Rate, by contrast, uses a single set of frame counts and therefore yields one value that represents the whole system, while still preserving the direct link to the per-interface load.

 

When the Traffic Profile is symmetric and bidirectional, as defined in Section 14 of [RFC2544], the Trial Forwarding Rate is numerically equal to the arithmetic average of the individual per-interface forwarding rates that would be produced by the RFC 2285 procedure.

 

For more complex traffic patterns, such as many-to-one as mentioned in Section 3.3.2 Partially Meshed Traffic of [RFC2285], the meaning of Trial Forwarding Rate is less straightforward. For example, if two input interfaces receive one million frames per second each, and a single interface outputs 1.4 million frames per second (fps), Trial Load is 1 million fps, Trial Loss Ratio is 30%, and Trial Forwarding Rate is 0.7 million fps.

 

Because this rate is anchored to the Load defined for one interface, a test report MAY show it either as the single averaged figure just described, or as the sum of the separate per-interface forwarding rates. For the example above, the aggregate trial forwarding rate is 1.4 million fps.

4.5.8. Trial Effective Duration

Definition:

 

Trial Effective Duration is a time quantity related to a Trial, by default equal to the Trial Duration.

Discussion:

 

This is an optional feature. If the Measurer does not return any Trial Effective Duration value, the Controller MUST use the Trial Duration value instead.

 

Trial Effective Duration may be any positive time quantity chosen by the Measurer to be used for time-based decisions in the Controller.

 

The test report MUST explain how the Measurer computes the returned Trial Effective Duration values, if they are not always equal to the Trial Duration.

 

This feature can be beneficial for time-critical benchmarks designed to manage the overall search duration, rather than solely the traffic portion of it. An approach is to measure the duration of the whole trial (including all wait times) and use that as the Trial Effective Duration.

 

This is also a way for the Measurer to inform the Controller about its surprising behavior, for example, when rounding the Trial Duration value.

4.5.9. Trial Output

Definition:

 

Trial Output is a composite quantity consisting of several attributes. Required attributes are: Trial Loss Ratio, Trial Effective Duration and Trial Forwarding Rate.

Discussion:

 

When referring to more than one trial, plural term "Trial Outputs" is used to collectively describe multiple Trial Output instances.

 

Measurer implementations may provide additional optional attributes. The Controller implementations SHOULD ignore values of any optional attribute they are not familiar with, except when passing Trial Output instances to the Manager.

 

Example of an optional attribute: The aggregate number of frames expected to be forwarded during the trial, especially if it is not (a rounded-down value) implied by Trial Load and Trial Duration.

 

While Section 3.5.2 of [RFC2285] requires the Offered Load value to be reported for forwarding rate measurements, it is not required in MLRsearch Specification, as search results do not depend on it.

4.5.10. Trial Result

Definition:

 

Trial Result is a composite quantity, consisting of the Trial Input and the Trial Output.

Discussion:

 

When referring to more than one trial, plural term "Trial Results" is used to collectively describe multiple Trial Result instances.

4.6. Goal Terms

This section defines new terms for quantities relevant (directly or indirectly) for inputs and outputs of the Controller component.

Several goal attributes are defined before introducing the main composite quantity: the Search Goal.

Contrary to other sections, definitions in subsections of this section are necessarily vague, as their fundamental meaning is to act as coefficients in formulas for Controller Output, which are not defined yet.

The discussions in this section relate the attributes to concepts mentioned in Section Overview of RFC 2544 Problems (Section 2), but even these discussion paragraphs are short, informal, and mostly referencing later sections, where the impact on search results is discussed after introducing the complete set of auxiliary terms.

4.6.1. Goal Final Trial Duration

Definition:

 

Minimal value for Trial Duration that must be reached. The value MUST be positive.

Discussion:

 

Certain trials must reach this minimum duration before a load can be classified as a lower bound.

 

The Controller may choose shorter durations, results of those may be enough for classification as an Upper Bound.

 

It is RECOMMENDED for all search goals to share the same Goal Final Trial Duration value. Otherwise, Trial Duration values larger than the Goal Final Trial Duration may occur, weakening the assumptions the Load Classification Logic (Section 6.1) is based on.

4.6.2. Goal Duration Sum

Definition:

 

A threshold value for a particular sum of Trial Effective Duration values. The value MUST be positive.

Discussion:

 

Informally, this prescribes the sufficient number of trials performed at a specific Trial Load and Goal Final Trial Duration during the search.

 

If the Goal Duration Sum is larger than the Goal Final Trial Duration, multiple trials may be needed to be performed at the same load.

 

Refer to Section MLRsearch Compliant with TST009 (Section 4.10.3) for an example where the possibility of multiple trials at the same load is intended.

 

A Goal Duration Sum value shorter than the Goal Final Trial Duration (of the same goal) could save some search time, but is NOT RECOMMENDED, as the time savings come at the cost of decreased repeatability.

 

In practice, the Search can spend less than Goal Duration Sum measuring a Load value when the results are particularly one-sided, but also, the Search can spend more than Goal Duration Sum measuring a Load when the results are balanced and include trials shorter than Goal Final Trial Duration.

4.6.3. Goal Loss Ratio

Definition:

 

A threshold value for Trial Loss Ratio values. The value MUST be non-negative and smaller than one.

Discussion:

 

A trial with Trial Loss Ratio larger than this value signals the SUT may be unable to process this Trial Load well enough.

 

See Throughput with Non-Zero Loss (Section 2.4) for reasons why users may want to set this value above zero.

 

Since multiple trials may be needed for one Load value, the Load Classification may be more complicated than mere comparison of Trial Loss Ratio to Goal Loss Ratio.

4.6.4. Goal Exceed Ratio

Definition:

 

A threshold value for a particular ratio of sums of Trial Effective Duration values. The value MUST be non-negative and smaller than one.

Discussion:

 

Informally, up to this proportion of Trial Results with Trial Loss Ratio above Goal Loss Ratio is tolerated at a Lower Bound. This is the full impact if every Trial was measured at Goal Final Trial Duration. The actual full logic is more complicated, as shorter Trials are allowed.

 

For explainability reasons, the RECOMMENDED value for exceed ratio is 0.5 (50%), as in practice that value leads to the smallest variation in overall Search Duration.

 

Refer to Section Exceed Ratio and Multiple Trials (Section 5.4) for more details.

4.6.5. Goal Width

Definition:

 

A threshold value for deciding whether two Trial Load values are close enough. This is an OPTIONAL attribute. If present, the value MUST be positive.

Discussion:

 

Informally, this acts as a stopping condition, controlling the precision of the search result. The search stops if every goal has reached its precision.

 

Implementations without this attribute MUST provide the Controller with other means to control the search stopping conditions.

 

Absolute load difference and relative load difference are two popular choices, but implementations may choose a different way to specify width.

 

The test report MUST make it clear what specific quantity is used as Goal Width.

 

It is RECOMMENDED to express Goal Width as a relative difference and setting it to a value not lower than the Goal Loss Ratio.

 

Refer to Section Generalized Throughput (Section 5.6) for more elaboration on the reasoning.

4.6.6. Goal Initial Trial Duration

Definition:

 

Minimal value for Trial Duration suggested to use for this goal. If present, this value MUST be positive.

Discussion:

 

This is an example of an optional Search Goal.

 

A typical default value is equal to the Goal Final Trial Duration value.

 

Informally, this is the shortest Trial Duration the Controller should select when focusing on the goal.

 

Note that shorter Trial Duration values can still be used, for example, selected while focusing on a different Search Goal. Such results MUST be still accepted by the Load Classification logic.

 

Goal Initial Trial Duration is a mechanism for a user to discourage trials with Trial Duration values deemed as too unreliable for a particular SUT and a given Search Goal.

4.6.7. Search Goal

Definition:

 

The Search Goal is a composite quantity consisting of several attributes, some of them are required.

 

Required attributes: Goal Final Trial Duration, Goal Duration Sum, Goal Loss Ratio and Goal Exceed Ratio.

 

Optional attributes: Goal Initial Trial Duration and Goal Width.

Discussion:

 

Implementations MAY add their own attributes. Those additional attributes may be required by an implementation even if they are not required by MLRsearch Specification. However, it is RECOMMENDED for those implementations to support missing attributes by providing typical default values.

 

For example, implementations with Goal Initial Trial Durations may also require users to specify "how quickly" should Trial Durations increase.

 

Refer to Section Section 4.10 for important Search Goal settings.

4.6.8. Controller Input

Definition:

 

Controller Input is a composite quantity required as an input for the Controller. The only REQUIRED attribute is a list of Search Goal instances.

Discussion:

 

MLRsearch implementations MAY use additional attributes. Those additional attributes may be required by an implementation even if they are not required by MLRsearch Specification.

 

Formally, the Manager does not apply any Controller configuration apart from one Controller Input instance.

 

For example, Traffic Profile is configured on the Measurer by the Manager, without explicit assistance of the Controller.

 

The order of Search Goal instances in a list SHOULD NOT have a big impact on Controller Output, but MLRsearch implementations MAY base their behavior on the order of Search Goal instances in a list.

4.6.8.1. Max Load

Definition:

 

Max Load is an optional attribute of Controller Input. It is the maximal value the Controller is allowed to use for Trial Load values.

Discussion:

 

Max Load is an example of an optional attribute (outside the list of Search Goals) required by some implementations of MLRsearch.

 

If the Max Load value is provided, Controller MUST NOT select Trial Load values larger than that value.

 

In theory, each search goal could have its own Max Load value, but as all Trial Results are possibly affecting all Search Goals, it makes more sense for a single Max Load value to apply to all Search Goal instances.

 

While Max Load is a frequently used configuration parameter, already governed (as maximum frame rate) by [RFC2544] (Section 20) and (as maximum offered load) by [RFC2285] (Section 3.5.3), some implementations may detect or discover it (instead of requiring a user-supplied value).

 

In MLRsearch Specification, one reason for listing the Relevant Upper Bound (Section 4.8.1) as a required attribute is that it makes the search result independent of Max Load value.

 

Given that Max Load is a quantity based on Load, Test Report MAY express this quantity using multi-interface values, as sum of per-interface maximal loads.

4.6.8.2. Min Load

Definition:

 

Min Load is an optional attribute of Controller Input. It is the minimal value the Controller is allowed to use for Trial Load values.

Discussion:

 

Min Load is another example of an optional attribute required by some implementations of MLRsearch. Similarly to Max Load, it makes more sense to prescribe one common value, as opposed to using a different value for each Search Goal.

 

If the Min Load value is provided, Controller MUST NOT select Trial Load values smaller than that value.

 

Min Load is mainly useful for saving time by failing early, arriving at an Irregular Goal Result when Min Load gets classified as an Upper Bound.

 

For implementations, it is RECOMMENDED to require Min Load to be non-zero and large enough to result in at least one frame being forwarded even at shortest allowed Trial Duration, so that Trial Loss Ratio is always well-defined, and the implementation can apply relative Goal Width safely.

 

Given that Min Load is a quantity based on Load, Test Report MAY express this quantity using multi-interface values, as sum of per-interface minimal loads.

4.7. Auxiliary Terms

While the terms defined in this section are not strictly needed when formulating MLRsearch requirements, they simplify the language used in discussion paragraphs and explanation sections.

4.7.1. Trial Classification

When one Trial Result instance is compared to one Search Goal instance, several relations can be named using short adjectives.

As trial results do not affect each other, this Trial Classification does not change during a Search.

4.7.1.1. High-Loss Trial

A trial with Trial Loss Ratio larger than a Goal Loss Ratio value is called a high-loss trial, with respect to given Search Goal (or lossy trial, if Goal Loss Ratio is zero).

4.7.1.2. Low-Loss Trial

If a trial is not high-loss, it is called a low-loss trial (or zero-loss trial, if Goal Loss Ratio is zero).

4.7.1.3. Short Trial

A trial with Trial Duration shorter than the Goal Final Trial Duration is called a short trial (with respect to the given Search Goal).

4.7.1.4. Full-Length Trial

A trial that is not short is called a full-length trial.

Note that this includes Trial Durations larger than Goal Final Trial Duration.

4.7.1.5. Long Trial

A trial with Trial Duration longer than the Goal Final Trial Duration is called a long trial.

4.7.2. Load Classification

When a set of all Trial Result instances, performed so far at one Trial Load, is compared to one Search Goal instance, their relation can be named using the concept of a bound.

In general, such bounds are a current quantity, even though cases of a Load changing its classification more than once during the Search is rare in practice.

4.7.2.1. Upper Bound

Definition:

 

A Load value is called an Upper Bound if and only if it is classified as such by Appendix A (Appendix A) algorithm for the given Search Goal at the current moment of the Search.

Discussion:

 

In more detail, the set of all Trial Result instances performed so far at the Trial Load (and any Trial Duration) is certain to fail to uphold all the requirements of the given Search Goal, mainly the Goal Loss Ratio in combination with the Goal Exceed Ratio. In this context, "certain to fail" relates to any possible results within the time remaining till Goal Duration Sum.

 

One search goal can have multiple different Trial Load values classified as its Upper Bounds. While search progresses and more trials are measured, any load value can become an Upper Bound in principle.

 

Moreover, a Load can stop being an Upper Bound, but that can only happen when more than Goal Duration Sum of trials are measured (e.g., because another Search Goal needs more trials at this load). Informally, the previous Upper Bound got invalidated. In practice, the Load frequently becomes a Lower Bound (Section 4.7.2.2) instead.

4.7.2.2. Lower Bound

Definition:

 

A Load value is called a Lower Bound if and only if it is classified as such by Appendix A (Appendix A) algorithm for the given Search Goal at the current moment of the search.

Discussion:

 

In more detail, the set of all Trial Result instances performed so far at the Trial Load (and any Trial Duration) is certain to uphold all the requirements of the given Search Goal, mainly the Goal Loss Ratio in combination with the Goal Exceed Ratio. Here "certain to uphold" relates to any possible results within the time remaining till Goal Duration Sum.

 

One search goal can have multiple different Trial Load values classified as its Lower Bounds. As search progresses and more trials are measured, any load value can become a Lower Bound in principle.

 

No load can be both an Upper Bound and a Lower Bound for the same Search goal at the same time, but it is possible for a larger load to be a Lower Bound while a smaller load is an Upper Bound.

 

Moreover, a Load can stop being a Lower Bound, but that can only happen when more than Goal Duration Sum of trials are measured (e.g., because another Search Goal needs more trials at this load). Informally, the previous Lower Bound got invalidated. In practice, the Load frequently becomes an Upper Bound (Section 4.7.2.1) instead.

4.7.2.3. Undecided

Definition:

 

A Load value is called Undecided if it is currently neither an Upper Bound nor a Lower Bound.

Discussion:

 

A Load value that has not been measured so far is Undecided.

 

It is possible for a Load to transition from an Upper Bound to Undecided by adding Short Trials with Low-Loss results. That is yet another reason for users to avoid using Search Goal instances with different Goal Final Trial Duration values.

4.8. Result Terms

Before defining the full structure of a Controller Output, it is useful to define the composite quantity, called Goal Result. The following subsections define its attribute first, before describing the Goal Result quantity.

There is a correspondence between Search Goals and Goal Results. Most of the following subsections refer to a given Search Goal, when defining their terms. Conversely, at the end of the search, each Search Goal instance has its corresponding Goal Result instance.

4.8.1. Relevant Upper Bound

Definition:

 

The Relevant Upper Bound is the smallest Trial Load value classified as an Upper Bound for a given Search Goal at the end of the Search.

Discussion:

 

If no measured load had enough High-Loss Trials, the Relevant Upper Bound MAY be non-existent. For example, when Max Load is classified as a Lower Bound.

 

Conversely, when Relevant Upper Bound does exist, it is not affected by Max Load value.

 

Given that Relevant Upper Bound is a quantity based on Load, Test Report MAY express this quantity using multi-interface values, as sum of per-interface loads.

4.8.2. Relevant Lower Bound

Definition:

 

The Relevant Lower Bound is the largest Trial Load value among those smaller than the Relevant Upper Bound, that got classified as a Lower Bound for a given Search Goal at the end of the search.

Discussion:

 

If no load had enough Low-Loss Trials, the Relevant Lower Bound MAY be non-existent.

 

Strictly speaking, if the Relevant Upper Bound does not exist, the Relevant Lower Bound also does not exist. In a typical case, Max Load is classified as a Lower Bound, making it impossible to increase the Load to continue the search for an Upper Bound. Thus, it is not clear whether a larger value would be found for a Relevant Lower Bound if larger Loads were possible.

 

Given that Relevant Lower Bound is a quantity based on Load, Test Report MAY express this quantity using multi-interface values, as sum of per-interface loads.

4.8.3. Conditional Throughput

Definition:

 

Conditional Throughput is a value computed at the Relevant Lower Bound according to algorithm defined in Appendix B (Appendix B).

Discussion:

 

The Relevant Lower Bound is defined only at the end of the Search, and so is the Conditional Throughput. But the algorithm can be applied at any time on any Lower Bound load, so the final Conditional Throughput value may appear sooner than at the end of a Search.

 

Informally, the Conditional Throughput should be a typical Trial Forwarding Rate, expected to be seen at the Relevant Lower Bound of a given Search Goal.

 

But frequently it is only a conservative estimate thereof, as MLRsearch implementations tend to stop measuring more Trials as soon as they confirm the value cannot get worse than this estimate within the Goal Duration Sum.

 

This value is RECOMMENDED to be used when evaluating repeatability and comparability of different MLRsearch implementations.

 

Refer to Section Generalized Throughput (Section 5.6) for more details.

 

Given that Conditional Throughput is a quantity based on Load, Test Report MAY express this quantity using multi-interface values, as sum of per-interface forwarding rates.

4.8.4. Goal Results

MLRsearch Specification is based on a set of requirements for a "regular" result. But in practice, it is not always possible for such result instance to exist, so also "irregular" results need to be supported.

4.8.4.1. Regular Goal Result

Definition:

 

Regular Goal Result is a composite quantity consisting of several attributes. Relevant Upper Bound and Relevant Lower Bound are REQUIRED attributes. Conditional Throughput is a RECOMMENDED attribute.

Discussion:

 

Implementations MAY add their own attributes.

 

Test report MUST display Relevant Lower Bound. Displaying Relevant Upper Bound is RECOMMENDED, especially if the implementation does not use Goal Width.

 

In general, stopping conditions for the corresponding Search Goal MUST be satisfied to produce a Regular Goal Result. Specifically, if an implementation offers Goal Width as a Search Goal attribute, the distance between the Relevant Lower Bound and the Relevant Upper Bound MUST NOT be larger than the Goal Width.

 

For stopping conditions refer to Sections Goal Width (Section 4.6.5) and Stopping Conditions and Precision (Section 5.2).

4.8.4.2. Irregular Goal Result

Definition:

 

Irregular Goal Result is a composite quantity. No attributes are required.

Discussion:

 

It is RECOMMENDED to report any useful quantity even if it does not satisfy all the requirements. For example, if Max Load is classified as a Lower Bound, it is fine to report it as an "effective" Relevant Lower Bound (although not a real one, as that requires Relevant Upper Bound which does not exist in this case), and compute Conditional Throughput for it. In this case, only the missing Relevant Upper Bound signals this result instance is irregular.

 

Similarly, if both relevant bounds exist, it is RECOMMENDED to include them as Irregular Goal Result attributes, and let the Manager decide if their distance is too far for Test Report purposes.

 

If Test Report displays some Irregular Goal Result attribute values, they MUST be clearly marked as coming from irregular results.

 

The implementation MAY define additional attributes, for example explicit flags for expected situations, so the Manager logic can be simpler.

4.8.4.3. Goal Result

Definition:

 

Goal Result is a composite quantity. Each instance is either a Regular Goal Result or an Irregular Goal Result.

Discussion:

 

The Manager MUST be able to distinguish whether the instance is regular or not.

4.8.5. Search Result

Definition:

 

The Search Result is a single composite object that maps each Search Goal instance to a corresponding Goal Result instance.

Discussion:

 

As an alternative to mapping, the Search Result may be represented as an ordered list of Goal Result instances that appears in the exact sequence of their corresponding Search Goal instances.

 

When the Search Result is expressed as a mapping, it MUST contain an entry for every Search Goal instance supplied in the Controller Input.

 

Identical Goal Result instances MAY be listed for different Search Goals, but their status as regular or irregular may be different. For example, if two goals differ only in Goal Width value, and the relevant bound values are close enough according to only one of them.

4.8.6. Controller Output

Definition:

 

The Controller Output is a composite quantity returned from the Controller to the Manager at the end of the search. The Search Result instance is its only required attribute.

Discussion:

 

MLRsearch implementation MAY return additional data in the Controller Output, e.g., number of trials performed and the total Search Duration.

4.9. Architecture Terms

MLRsearch architecture consists of three main system components: the Manager, the Controller, and the Measurer. The components were introduced in Architecture Overview (Section 4.2), and the following subsections finalize their definitions using terms from previous sections.

Note that the architecture also implies the presence of other components, such as the SUT and the tester (as a sub-component of the Measurer).

Communication protocols and interfaces between components are left unspecified. For example, when MLRsearch Specification mentions "Controller calls Measurer", it is possible that the Controller notifies the Manager to call the Measurer indirectly instead. In doing so, the Measurer implementations can be fully independent from the Controller implementations, e.g., developed in different programming languages.

4.9.1. Measurer

Definition:

 

The Measurer is a functional element that when called with a Trial Input (Section 4.5.3) instance, performs one Trial (Section 4.4.3) and returns a Trial Output (Section 4.5.9) instance.

Discussion:

 

This definition assumes the Measurer is already initialized. In practice, there may be additional steps before the Search, e.g., when the Manager configures the traffic profile (either on the Measurer or on its tester sub-component directly) and performs a warm-up (if the tester or the test procedure requires one).

 

It is the responsibility of the Measurer implementation to uphold any requirements and assumptions present in MLRsearch Specification, e.g., Trial Forwarding Ratio not being larger than one.

 

Implementers have some freedom. For example, Section 10 of [RFC2544] gives some suggestions (but not requirements) related to duplicated or reordered frames. Implementations are RECOMMENDED to document their behavior related to such freedoms in as detailed a way as possible.

 

It is RECOMMENDED to benchmark the test equipment first, e.g., connect sender and receiver directly (without any SUT in the path), find a load value that guarantees the Offered Load is not too far from the Intended Load and use that value as the Max Load value. When testing the real SUT, it is RECOMMENDED to turn any severe deviation between the Intended Load and the Offered Load into increased Trial Loss Ratio.

 

Neither of the two recommendations are made into mandatory requirements, because it is not easy to provide guidance about when the difference is severe enough, in a way that would be disentangled from other Measurer freedoms.

 

For a sample situation where the Offered Load cannot keep up with the Intended Load, and the consequences on MLRsearch result, refer to Section Hard Performance Limit (Section 5.6.1).

4.9.2. Controller

Definition:

 

The Controller is a functional element that, upon receiving a Controller Input instance, repeatedly generates Trial Input instances for the Measurer and collects the corresponding Trial Output instances. This cycle continues until the stopping conditions are met, at which point the Controller produces a final Controller Output instance and terminates.

Discussion:

 

Informally, the Controller has big freedom in selection of Trial Inputs, and the implementations want to achieve all the Search Goals in the shortest average time.

 

The Controller's role in optimizing the overall Search Duration distinguishes MLRsearch algorithms from simpler search procedures.

 

Informally, each implementation can have different stopping conditions. Goal Width is only one example. In practice, implementation details do not matter, as long as Goal Result instances are regular.

4.9.3. Manager

Definition:

 

The Manager is a functional element that is reponsible for provisioning other components, calling a Controller component once, and for creating the test report following the reporting format as defined in Section 26 of [RFC2544].

Discussion:

 

The Manager initializes the SUT, the Measurer (and the tester if independent from Measurer) with their intended configurations before calling the Controller.

 

Note that Section 7 of [RFC2544] already puts requirements on SUT setups:

 

"It is expected that all of the tests will be run without changing the configuration or setup of the DUT in any way other than that required to do the specific test. For example, it is not acceptable to change the size of frame handling buffers between tests of frame handling rates or to disable all but one transport protocol when testing the throughput of that protocol."

 

It is REQUIRED for the test report to encompass all the SUT configuration details, including description of a "default" configuration common for most tests and configuration changes if required by a specific test.

 

For example, Section 5.1.1 of [RFC5180] recommends testing jumbo frames if SUT can forward them, even though they are outside the scope of the 802.3 IEEE standard. In this case, it is acceptable for the SUT default configuration to not support jumbo frames, and only enable this support when testing jumbo traffic profiles, as the handling of jumbo frames typically has different packet buffer requirements and potentially higher processing overhead. Non-jumbo frame sizes should also be tested on the jumbo-enabled setup.

 

The Manager does not need to be able to tweak any Search Goal attributes, but it MUST report all applied attribute values even if not tweaked.

 

A "user" - human or automated - invokes the Manager once to launch a single Search and receive its report. Every new invocation is treated as a fresh, independent Search; how the system behaves across multiple calls (for example, combining or comparing their results) is explicitly out of scope for this document.

4.10. Compliance

This section discusses compliance relations between MLRsearch and other test procedures.

4.10.1. Test Procedure Compliant with MLRsearch

Any networking measurement setup that could be understood as consisting of functional elements satisfying requirements for the Measurer, the Controller and the Manager, is compliant with MLRsearch Specification.

These components can be seen as abstractions present in any testing procedure. For example, there can be a single component acting both as the Manager and the Controller, but if values of required attributes of Search Goals and Goal Results are visible in the test report, the Controller Input instance and Controller Output instance are implied.

For example, any setup for conditionally (or unconditionally) compliant [RFC2544] throughput testing can be understood as a MLRsearch architecture, if there is enough data to reconstruct the Relevant Upper Bound.

Refer to section MLRsearch Compliant with RFC 2544 (Section 4.10.2) for an equivalent Search Goal.

Any test procedure that can be understood as one call to the Manager of MLRsearch architecture is said to be compliant with MLRsearch Specification.

4.10.2. MLRsearch Compliant with RFC 2544

The following Search Goal instance makes the corresponding Search Result unconditionally compliant with Section 24 of [RFC2544].

  • Goal Final Trial Duration = 60 seconds

  • Goal Duration Sum = 60 seconds

  • Goal Loss Ratio = 0%

  • Goal Exceed Ratio = 0%

Goal Loss Ratio and Goal Exceed Ratio attributes, are enough to make the Search Goal conditionally compliant. Adding Goal Final Trial Duration makes the Search Goal unconditionally compliant.

Goal Duration Sum prevents MLRsearch from repeating zero-loss Full-Length Trials.

The presence of other Search Goals does not affect the compliance of this Goal Result. The Relevant Lower Bound and the Conditional Throughput are in this case equal to each other, and the value is the [RFC2544] throughput.

Non-zero exceed ratio is not strictly disallowed, but it could needlessly prolong the search when Low-Loss short trials are present.

4.10.3. MLRsearch Compliant with TST009

One of the alternatives to [RFC2544] is Binary search with loss verification as described in Section 12.3.3 of [TST009].

The rationale of such search is to repeat high-loss trials, hoping for zero loss on second try, so the results are closer to the noiseless end of performance spectrum, thus more repeatable and comparable.

Only the variant with "z = infinity" is achievable with MLRsearch.

For example, for "max(r) = 2" variant, the following Search Goal instance should be used to get compatible Search Result:

  • Goal Final Trial Duration = 60 seconds

  • Goal Duration Sum = 120 seconds

  • Goal Loss Ratio = 0%

  • Goal Exceed Ratio = 50%

If the first 60 seconds trial has zero loss, it is enough for MLRsearch to stop measuring at that load, as even a second high-loss trial would still fit within the exceed ratio.

But if the first trial is high-loss, MLRsearch needs to perform also the second trial to classify that load. Goal Duration Sum is twice as long as Goal Final Trial Duration, so third full-length trial is never needed.

5. Methodology Rationale and Design Considerations

This section explains the Why behind MLRsearch. Building on the normative specification in Section MLRsearch Specification (Section 4), it contrasts MLRsearch with the classic [RFC2544] single-ratio binary-search procedure and walks through the key design choices: binary-search mechanics, stopping-rule precision, loss-inversion for multiple goals, exceed-ratio handling, short-trial strategies, and the generalised throughput concept. Together, these considerations show how the methodology reduces test time, supports multiple loss ratios, and improves repeatability.

5.2. Stopping Conditions and Precision

MLRsearch Specification requires listing both Relevant Bounds for each Search Goal, and the difference between the bounds implies whether the result precision is achieved. Therefore, it is not necessary to report the specific stopping condition used.

MLRsearch implementations may use Goal Width to allow direct control of result precision and indirect control of the Search Duration.

Other MLRsearch implementations may use different stopping conditions: for example based on the Search Duration, trading off precision control for duration control.

Due to various possible time optimizations, there is no strict correspondence between the Search Duration and Goal Width values. In practice, noisy SUT performance increases both average search time and its variance.

5.3. Loss Ratios and Loss Inversion

The biggest

difference between MLRsearch and [RFC2544] binary search is in the goals of the search. [RFC2544] has a single goal, based on classifying a single full-length trial as either zero-loss or non-zero-loss. MLRsearch supports searching for multiple Search Goals at once, usually differing in their Goal Loss Ratio values.

5.3.1. Single Goal and Hard Bounds

Each bound in [RFC2544] simple binary search is "hard", in the sense that all further Trial Load values are smaller than any current upper bound and larger than any current lower bound.

This is also possible for MLRsearch implementations, when the search is started with only one Search Goal instance.

5.3.2. Multiple Goals and Loss Inversion

MLRsearch Specification

supports multiple Search Goals, making the search procedure more complicated compared to binary search with single goal, but most of the complications do not affect the final results much. Except for one phenomenon: Loss Inversion.

Depending on Search Goal attributes, Load Classification results may be resistant to small amounts of Section Inconsistent Trial Results (Section 2.5). However, for larger amounts, a Load that is classified as an Upper Bound for one Search Goal may still be a Lower Bound for another Search Goal. Due to this other goal, MLRsearch will probably perform subsequent Trials at Trial Loads even larger than the original value.

This introduces questions any many-goals search algorithm has to address. For example: What to do when all such larger load trials happen to have zero loss? Does it mean the earlier upper bound was not real? Does it mean the later Low-Loss trials are not considered a lower bound?

The situation where a smaller Load is classified as an Upper Bound, while a larger Load is classified as a Lower Bound (for the same search goal), is called Loss Inversion.

Conversely, only single-goal search algorithms can have hard bounds that shield them from Loss Inversion.

5.3.3. Conservativeness and Relevant Bounds

MLRsearch is conservative when dealing with Loss Inversion: the Upper Bound is considered real, and the Lower Bound is considered to be a fluke, at least when computing the final result.

This is formalized using definitions of Relevant Upper Bound (Section 4.8.1) and Relevant Lower Bound (Section 4.8.2).

The Relevant Upper Bound (for specific goal) is the smallest Load classified as an Upper Bound. But the Relevant Lower Bound is not simply the largest among Lower Bounds. It is the largest Load among Loads that are Lower Bounds while also being smaller than the Relevant Upper Bound.

With these definitions, the Relevant Lower Bound is always smaller than the Relevant Upper Bound (if both exist), and the two relevant bounds are used analogously as the two tightest bounds in the binary search. When they meet the stopping conditions, the Relevant Bounds are used in the output.

5.3.4. Consequences

The consequence of the way the Relevant Bounds are defined is that every Trial Result can have an impact on any current Relevant Bound larger than that Trial Load, namely by becoming a new Upper Bound.

This also applies when that Load is measured before another Load gets enough measurements to become a current Relevant Bound.

This also implies that if the SUT tested (or the Traffic Generator used) needs a warm-up, it should be warmed up before starting the Search, otherwise the first few measurements could become unjustly limiting.

For MLRsearch implementations, it means it is better to measure at smaller Loads first, so bounds found earlier are less likely to get invalidated later.

5.4. Exceed Ratio and Multiple Trials

The idea of performing multiple Trials at the same Trial Load comes from a model where some Trial Results (those with high Trial Loss Ratio) are affected by infrequent effects, causing unsatisfactory repeatability

of [RFC2544] Throughput results. Refer to Section DUT in SUT (Section 2.2) for a discussion about noiseful and noiseless ends of the SUT performance spectrum. Stable results are closer to the noiseless end of the SUT performance spectrum, so MLRsearch may need to allow some frequency of high-loss trials to ignore the rare but big effects near the noiseful end.

For MLRsearch to perform such Trial Result filtering, it needs a configuration option to tell how frequent the "infrequent" big loss can be. This option is called the Goal Exceed Ratio (Section 4.6.4). It tells MLRsearch what ratio of trials (more specifically, what ratio of Trial Effective Duration seconds) can have a Trial Loss Ratio (Section 4.5.6) larger than the Goal Loss Ratio (Section 4.6.3) and still be classified as a Lower Bound (Section 4.7.2.2).

Zero exceed ratio means all Trials must have a Trial Loss Ratio equal to or lower than the Goal Loss Ratio.

When more than one Trial is intended to classify a Load, MLRsearch also needs something that controls the number of trials needed. Therefore, each goal also has an attribute called Goal Duration Sum.

The meaning of a Goal Duration Sum (Section 4.6.2) is that when a Load has (Full-Length) Trials whose Trial Effective Durations when summed up give a value at least as big as the Goal Duration Sum value, the Load is guaranteed to be classified either as an Upper Bound or a Lower Bound for that Search Goal instance.

5.5. Short Trials and Duration Selection

MLRsearch requires each Search Goal to specify its Goal Final Trial Duration.

Section 24 of [RFC2544] already anticipates possible time savings when Short Trials are used.

An MLRsearch implementation MAY expose configuration parameters that decide whether, when, and how short trial durations are used. The exact heuristics and controls are left to the discretion of the implementer.

While MLRsearch implementations are free to use any logic to select Trial Input values, comparability between MLRsearch implementations is only assured when the Load Classification logic handles any possible set of Trial Results in the same way.

The presence of Short Trial Results complicates the Load Classification logic, see more details in Section Load Classification Logic (Section 6.1).

While the Load Classification algorithm is designed to avoid any unneeded Trials, for explainability reasons it is recommended for users to use such Controller Input instances that lead to all Trial Duration values selected by Controller to be the same, e.g., by setting any Goal Initial Trial Duration to be a single value also used in all Goal Final Trial Duration attributes.

5.6. Generalized Throughput

Because testing equipment takes the Intended Load as an input parameter for a Trial measurement, any load search algorithm needs to deal with Intended Load values internally.

But in the presence of Search Goals with a non-zero Goal Loss Ratio (Section 4.6.3), the Load usually does not match the user's intuition of what a throughput is. The forwarding rate as defined in Section Section 3.6.1 of [RFC2285] is better, but it is not obvious how to generalize it for Loads with multiple Trials and a non-zero Goal Loss Ratio.

The clearest illustration - and the chief reason for adopting a generalized throughput definition - is the presence of a hard performance limit.

5.6.1. Hard Performance Limit

Even if bandwidth of a medium allows higher traffic forwarding performance, the SUT interfaces may have their additional own limitations, e.g., a specific frames-per-second limit on the NIC (a common occurrence).

Those limitations should be known and provided as Max Load, Section Max Load (Section 4.6.8.1).

But if Max Load is set larger than what the interface can receive or transmit, there will be a "hard limit" behavior observed in Trial Results.

Consider that the hard limit is at hundred million frames per second (100 Mfps), Max Load is larger, and the Goal Loss Ratio is 0.5%. If DUT has no additional losses, 0.5% Trial Loss Ratio will be achieved at Relevant Lower Bound of 100.5025 Mfps.

Reporting a throughput that exceeds the SUT's verified hard limit is counter-intuitive. Accordingly, the [RFC2544] Throughput metric should be generalized - rather than relying solely on the Relevant Lower Bound - to reflect realistic, limit-aware performance.

MLRsearch defines one such generalization, the Conditional Throughput (Section 4.8.3). It is the Trial Forwarding Rate from one of the Full-Length Trials performed at the Relevant Lower Bound. The algorithm to determine which trial exactly is in Appendix B (Appendix B).

In the hard limit example, 100.5025 Mfps Load will still have only 100.0 Mfps forwarding rate, nicely confirming the known limitation.

5.6.2. Performance Variability

With non-zero Goal Loss Ratio, and without hard performance limits, Low-Loss trials at the same Load may achieve different Trial Forwarding Rate values just due to DUT performance variability.

By comparing the best case (all Relevant Lower Bound trials have zero loss) and the worst case (all Trial Loss Ratios at Relevant Lower Bound are equal to the Goal Loss Ratio), one can prove that Conditional Throughput values may have up to the Goal Loss Ratio relative difference.

Setting the Goal Width below the Goal Loss Ratio may cause the Conditional Throughput for a larger Goal Loss Ratio to become smaller than a Conditional Throughput for a goal with a lower Goal Loss Ratio, which is counter-intuitive, considering they come from the same Search. Therefore, it is RECOMMENDED to set the Goal Width to a value no lower than the Goal Loss Ratio of the higher-loss Search Goal.

Although Conditional Throughput can fluctuate from one run to the next, it still offers a more discriminating basis for comparison than the Relevant Lower Bound - particularly when deterministic load selection yields the same Lower Bound value across multiple runs.

6. MLRsearch Logic and Example

This section uses informal language to describe two aspects of MLRsearch logic: Load Classification and Conditional Throughput, reflecting formal pseudocode representation provided in Appendix A (Appendix A) and Appendix B (Appendix B). This is followed by example search.

The logic is equivalent but not identical to the pseudocode on appendices. The pseudocode is designed to be short and frequently combines multiple operations into one expression. The logic as described in this section lists each operation separately and uses more intuitive names for the intermediate values.

6.1. Load Classification Logic

Note: For explanation clarity variables are taged as (I)nput, (T)emporary, (O)utput.

  • Collect Trial Results:

    • Take all Trial Result instances (I) measured at a given load.

  • Aggregate Trial Durations:

    • Full-length high-loss sum (T) is the sum of Trial Effective Duration values of all full-length high-loss trials (I).

    • Full-length low-loss sum (T) is the sum of Trial Effective Duration values of all full-length low-loss trials (I).

    • Short high-loss sum is the sum (T) of Trial Effective Duration values of all short high-loss trials (I).

    • Short low-loss sum is the sum (T) of Trial Effective Duration values of all short low-loss trials (I).

  • Derive goal-based ratios:

    • Subceed ratio (T) is One minus the Goal Exceed Ratio (I).

    • Exceed coefficient (T) is the Goal Exceed Ratio divided by the subceed ratio.

  • Balance short-trial effects:

    • Balancing sum (T) is the short low-loss sum multiplied by the exceed coefficient.

    • Excess sum (T) is the short high-loss sum minus the balancing sum.

    • Positive excess sum (T) is the maximum of zero and excess sum.

  • Compute effective duration totals

    • Effective high-loss sum (T) is the full-length high-loss sum plus the positive excess sum.

    • Effective full sum (T) is the effective high-loss sum plus the full-length low-loss sum.

    • Effective whole sum (T) is the larger of the effective full sum and the Goal Duration Sum.

    • Missing sum (T) is the effective whole sum minus the effective full sum.

  • Estimate exceed ratios:

    • Pessimistic high-loss sum (T) is the effective high-loss sum plus the missing sum.

    • Optimistic exceed ratio (T) is the effective high-loss sum divided by the effective whole sum.

    • Pessimistic exceed ratio (T) is the pessimistic high-loss sum divided by the effective whole sum.

  • Classify the Load:

    • The load is classified as an Upper Bound (O) if the optimistic exceed ratio is larger than the Goal Exceed Ratio.

    • The load is classified as a Lower Bound (O) if the pessimistic exceed ratio is not larger than the Goal Exceed Ratio.

    • The load is classified as undecided (O) otherwise.

6.2. Conditional Throughput Logic

  • Collect Trial Results

    • Take all Trial Result instances (I) measured at a given Load.

  • Sum Full-Length Durations:

    • Full-length high-loss sum (T) is the sum of Trial Effective Duration values of all full-length high-loss trials (I).

    • Full-length low-loss sum (T) is the sum of Trial Effective Duration values of all full-length low-loss trials (I).

    • Full-length sum (T) is the full-length high-loss sum (I) plus the full-length low-loss sum (I).

  • Derive initial thresholds:

    • Subceed ratio (T) is One minus the Goal Exceed Ratio (I) is called.

    • Remaining sum (T) initially is full-lengths sum multiplied by subceed ratio.

    • Current loss ratio (T) initially is 100%.

  • Iterate through ordered trials

    • For each full-length trial result, sorted in increasing order by Trial Loss Ratio:

      • If remaining sum is not larger than zero, exit the loop.

      • Set current loss ratio to this trial's Trial Loss Ratio (I).

      • Decrease the remaining sum by this trial's Trial Effective Duration (I).

  • Compute Conditional Throughput

    • Current forwarding ratio (T) is One minus the current loss ratio.

    • Conditional Throughput (T) is the current forwarding ratio multiplied by the Load value.

6.2.1. Conditional Throughput and Load Classification

Conditional Throughput and results of Load Classification overlap but are not identical.

  • When a load is marked as a Relevant Lower Bound, its Conditional Throughput is taken from a trial whose loss ratio never exceeds the Goal Loss Ratio.

  • The reverse is not guaranteed: if the Goal Width is narrower than the Goal Loss Ratio, Conditional Throughput can still end up higher than the Relevant Upper Bound.

6.3. SUT Behaviors

In Section DUT in SUT (Section 2.2), the notion of noise has been introduced. This section uses new terms to describe possible SUT behaviors more precisely.

From measurement point of view, noise is visible as inconsistent trial results. See Inconsistent Trial Results (Section 2.5) for general points and Loss Ratios and Loss Inversion (Section 5.3) for specifics when comparing different Load values.

Load Classification and Conditional Throughput apply to a single Load value, but even the set of Trial Results measured at that Trial Load value may appear inconsistent.

As MLRsearch aims to save time, it executes only a small number of Trials, getting only a limited amount of information about SUT behavior. It is useful to introduce an "SUT expert" point of view to contrast with that limited information.

6.3.1. Expert Predictions

Imagine that before the Search starts, a human expert had unlimited time to measure SUT and obtain all reliable information about it. The information is not perfect, as there is still random noise influencing SUT. But the expert is familiar with possible noise events, even the rare ones, and thus the expert can do probabilistic predictions about future Trial Outputs.

When several outcomes are possible, the expert can assess probability of each outcome.

6.3.2. Exceed Probability

When the Controller selects new Trial Duration and Trial Load, and just before the Measurer starts performing the Trial, the SUT expert can envision possible Trial Results.

With respect to a particular Search Goal instance, the possibilities can be summarized into a single number: Exceed Probability. It is the probability (according to the expert) that the measured Trial Loss Ratio will be higher than the Goal Loss Ratio.

6.3.3. Trial Duration Dependence

When comparing Exceed Probability values for the same Trial Load value but different Trial Duration values, there are several patterns that commonly occur in practice.

6.3.3.1. Strong Increase

Exceed Probability is very low at short durations but very high at full-length. This SUT behavior is undesirable, and may hint at faulty SUT, e.g., SUT leaks resources and is unable to sustain the desired performance.

But this behavior is also seen when SUT uses large amount of buffers. This is the main reasons users may want to set large Goal Final Trial Duration.

6.3.3.2. Mild Increase

Short trials are slightly less likely to exceed the loss-ratio limit, but the improvement is modest. This mild benefit is typical when noise is dominated by rare, large loss spikes: during a full-length trial, the good-performing periods cannot fully offset the heavy frame loss that occurs in the brief low-performing bursts.

6.3.3.3. Independence

Short trials have basically the same Exceed Probability as full-length trials. This is possible only if loss spikes are small (so other parts can compensate) and if Goal Loss Ratio is more than zero (otherwise, other parts cannot compensate at all).

6.3.3.4. Decrease

Short trials have larger Exceed Probability than full-length trials. This can be possible only for non-zero Goal Loss Ratio, for example if SUT needs to "warm up" to best performance within each trial. Not commonly seen in practice.

7. IANA Considerations

This document does not make any request to IANA.

8. Security Considerations

Benchmarking activities as described in this memo are limited to technology characterization of a DUT/SUT using controlled stimuli in a laboratory environment, with dedicated address space and the constraints specified in the sections above.

The benchmarking network topology will be an independent test setup and MUST NOT be connected to devices that may forward the test traffic into a production network or misroute traffic to the test management network.

Further, benchmarking is performed on an "opaque" basis, relying solely on measurements observable external to the DUT/SUT.

The DUT/SUT SHOULD NOT include features that serve only to boost benchmark scores - such as a dedicated "fast-track" test mode that is never used in normal operation.

Any implications for network security arising from the DUT/SUT SHOULD be identical in the lab and in production networks.

9. Acknowledgements

Special wholehearted gratitude and thanks to the late Al Morton for his thorough reviews filled with very specific feedback and constructive guidelines. Thank You Al for the close collaboration over the years, Your Mentorship, Your continuous unwavering encouragement full of empathy and energizing positive attitude. Al, You are dearly missed.

Thanks to Gabor Lencse, Giuseppe Fioccola and BMWG contributors for good discussions and thorough reviews, guiding and helping us to improve the clarity and formality of this document.

Many thanks to Alec Hothan of the OPNFV NFVbench project for a thorough review and numerous useful comments and suggestions in the earlier versions of this document.

10. References

10.1. Normative References

[RFC1242]
Bradner, S., "Benchmarking Terminology for Network Interconnection Devices", RFC 1242, DOI 10.17487/RFC1242, , <https://www.rfc-editor.org/info/rfc1242>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC2285]
Mandeville, R., "Benchmarking Terminology for LAN Switching Devices", RFC 2285, DOI 10.17487/RFC2285, , <https://www.rfc-editor.org/info/rfc2285>.
[RFC2544]
Bradner, S. and J. McQuaid, "Benchmarking Methodology for Network Interconnect Devices", RFC 2544, DOI 10.17487/RFC2544, , <https://www.rfc-editor.org/info/rfc2544>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.

10.2. Informative References

[FDio-CSIT-MLRsearch]
"FD.io CSIT Test Methodology - MLRsearch", , <https://csit.fd.io/cdocs/methodology/measurements/data_plane_throughput/mlr_search/>.
[Lencze-Kovacs-Shima]
"Gaming with the Throughput and the Latency Benchmarking Measurement Procedures of RFC 2544", n.d., <http://dx.doi.org/10.11601/ijates.v9i2.288>.
[Lencze-Shima]
"An Upgrade to Benchmarking Methodology for Network Interconnect Devices - expired", n.d., <https://datatracker.ietf.org/doc/html/draft-lencse-bmwg-rfc2544-bis-00>.
[Ott-Mathis-Semke-Mahdavi]
"The Macroscopic Behavior of the TCP Congestion Avoidance Algorithm", n.d., <https://www.cs.cornell.edu/people/egs/cornellonly/syslunch/fall02/ott.pdf>.
[PyPI-MLRsearch]
"MLRsearch 1.2.1, Python Package Index", , <https://pypi.org/project/MLRsearch/1.2.1/>.
[RFC5180]
Popoviciu, C., Hamza, A., Van de Velde, G., and D. Dugatkin, "IPv6 Benchmarking Methodology for Network Interconnect Devices", RFC 5180, DOI 10.17487/RFC5180, , <https://www.rfc-editor.org/info/rfc5180>.
[RFC6349]
Constantine, B., Forget, G., Geib, R., and R. Schrage, "Framework for TCP Throughput Testing", RFC 6349, DOI 10.17487/RFC6349, , <https://www.rfc-editor.org/info/rfc6349>.
[RFC6985]
Morton, A., "IMIX Genome: Specification of Variable Packet Sizes for Additional Testing", RFC 6985, DOI 10.17487/RFC6985, , <https://www.rfc-editor.org/info/rfc6985>.
[RFC8219]
Georgescu, M., Pislaru, L., and G. Lencse, "Benchmarking Methodology for IPv6 Transition Technologies", RFC 8219, DOI 10.17487/RFC8219, , <https://www.rfc-editor.org/info/rfc8219>.
[TST009]
"TST 009", n.d., <https://www.etsi.org/deliver/etsi_gs/NFV-TST/001_099/009/03.04.01_60/gs_NFV-TST009v030401p.pdf>.
[Vassilev]
"A YANG Data Model for Network Tester Management", n.d., <https://datatracker.ietf.org/doc/draft-ietf-bmwg-network-tester-cfg/06>.
[Y.1564]
"Y.1564", n.d., <https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-Y.1564-201602-I!!PDF-E&type=items>.

Appendix A. Load Classification Code

This appendix specifies how to perform the Load Classification.

Any Trial Load value can be classified, according to a given Search Goal (Section 4.6.7) instance.

The algorithm uses (some subsets of) the set of all available Trial Results from Trials measured at a given Load at the end of the Search.

The block at the end of this appendix holds pseudocode which computes two values, stored in variables named optimistic_is_lower and pessimistic_is_lower.

Although presented as pseudocode, the listing is syntactically valid Python and can be executed without modification.

If values of both variables are computed to be true, the Load in question is classified as a Lower Bound according to the given Search Goal instance. If values of both variables are false, the Load is classified as an Upper Bound. Otherwise, the load is classified as Undecided.

Some variable names are shortened to fit expressions in one line. Namely, variables holding sum quantities end in _s instead of _sum, and variables holding effective quantities start in effect_ instead of effective_.

The pseudocode expects the following variables to hold the following values:

The code works correctly also when there are no Trial Results at a given Load.

<CODE BEGINS>
exceed_coefficient = goal_exceed_ratio / (1.0 - goal_exceed_ratio)
balancing_s = short_low_loss_s * exceed_coefficient
positive_excess_s = max(0.0, short_high_loss_s - balancing_s)
effect_high_loss_s = full_length_high_loss_s + positive_excess_s
effect_full_length_s = full_length_low_loss_s + effect_high_loss_s
effect_whole_s = max(effect_full_length_s, goal_duration_s)
quantile_duration_s = effect_whole_s * goal_exceed_ratio
pessimistic_high_loss_s = effect_whole_s - full_length_low_loss_s
pessimistic_is_lower = pessimistic_high_loss_s <= quantile_duration_s
optimistic_is_lower = effect_high_loss_s <= quantile_duration_s
<CODE ENDS>

Appendix B. Conditional Throughput Code

This section specifies an example of how to compute Conditional Throughput, as referred to in Section Conditional Throughput (Section 4.8.3).

Any Load value can be used as the basis for the following computation, but only the Relevant Lower Bound (at the end of the Search) leads to the value called the Conditional Throughput for a given Search Goal.

The algorithm uses (some subsets of) the set of all available Trial Results from Trials measured at a given Load at the end of the Search.

The block at the end of this appendix holds pseudocode which computes a value stored as variable conditional_throughput.

Although presented as pseudocode, the listing is syntactically valid Python and can be executed without modification.

Some variable names are shortened in order to fit expressions in one line. Namely, variables holding sum quantities end in _s instead of _sum, and variables holding effective quantities start in effect_ instead of effective_.

The pseudocode expects the following variables to hold the following values:

The code works correctly only when there is at least one Trial Result measured at a given Load.

<CODE BEGINS>
full_length_s = full_length_low_loss_s + full_length_high_loss_s
whole_s = max(goal_duration_s, full_length_s)
remaining = whole_s * (1.0 - goal_exceed_ratio)
quantile_loss_ratio = None
for trial in full_length_trials:
    if quantile_loss_ratio is None or remaining > 0.0:
        quantile_loss_ratio = trial.loss_ratio
        remaining -= trial.effect_duration
    else:
        break
else:
    if remaining > 0.0:
        quantile_loss_ratio = 1.0
conditional_throughput = intended_load * (1.0 - quantile_loss_ratio)
<CODE ENDS>

Authors' Addresses

Maciek Konstantynowicz
Cisco Systems
Vratko Polak
Cisco Systems